Home


PROCESS PARAMETER IN SPINNING - 2

spinning frame

Page 1   2

  • RING AND TRAVELLER:

  • Ring diameter, flange width and ring profile depends upon the fibre, twist per inch, lift of the
    machine,maximum spindle speed, winding capacity etc.
  • Operating speed of the traveller has a maximum limit, because the heat generated between ring and
    traveller should be dissipated by the low mass of the traveller with in a short time available.
  • If the cotton combed yarn is for knitting, traveller speed will not be a limiting factor. Since yarn
    TPI is less, the yarn strand is not strong enough. Therefore the limiting factor will be yarn tension.

  • Following points to be considered

    1. for 12s to 24s , 42mm ring with 180 mm lift can be used
    2. for 24s to 36s, 40 mm ring with 180 lift can be used
    3. for 36s to 60s , 38 mm ring with 170 mm lift can be used
    4. for 70s to 120s, 36 mmring with 160 mm lift can be used.
    5. If winding is a problem, it is better to go for reduced production with bigger ring dia.
    6. Anti-wedge ring profile is better, because of better heat dissipation
    7. Elliptical traveller should be used, to avoid start-up breaks in hosiery counts
    8. special type of travller clearer can be used to avoid accumulation of fibre on the traveller
      as traveller with waste does not perform well during start-up.
  • For polyester/cotton blends and cotton weaving counts yarn strength is not a problem. The limiting
    factor will be a traveller speed. For a ring diameter of 40 mm, spindle speed upto 19500 should not
    be a problem. Rings like Titan(from Braecker), NCN(bergosesia) etc, will be able to meet the requirements.
  • For spindle speeds more than 20000 rpm, ORBIT rings or SU-RINGS should be used. As the area of
    contact is more with this rings, with higher speeds and pressure, the heat produced can be dissipated without any problem. Normal ring and traveller profile will not be able to run at speeds higher than 20000 to produce a good quality yarn.
  • ORBIT rings will be of great help, to work 100% polyester at higher spindle speeds. Because,
    of the tension, the heat produced between ring and traveller is extremely high. But one should understand,
    that ,the yarn strength of polyester is very high. Here the limiting factor is only the heat dissipation.
    Therefore ORBIT RINGS with high area of contact will be able to run well at higher spindle speeds when processing 100% polyester.
  • While running 100% cotton, the fibre dust in cotton, acts like a lubricant. All the cottons do
    not form same amount of lubricating film. If there is no fibre lubrication, traveller wears out
    very fast. Because of this worn out or burn out travellers, microwelding occurs on the ring surface,<
    which results in damaged ring surface, hence imperfections and hairiness increases in the yarn.
  • Lubrication is good with west african cottons. It may not be true with all the cottons from
    West africa. In general there is a feeling, cottons from Russia, or from very dry places, lubrication
    is very bad. If the fibre lubrication is very bad, it is better to use lighter travellers and change
    the travellers as early as possible.
  • Traveller life depends upon the type of raw material, humidity conditions, ringframe speeds,
    the yarn count, etc. If the climate is dry , fibre lubrication will be less while processing cotton.
  • Traveller life is very less when Viscose rayon is processed especially semi dull fibre, because of
    low lubrication. Traveller life is better for optical bright fibres.
  • Traveller life is better for Poly/cotton blends, because of better lubricatiion between ring and
    traveller.
  • Because of the centrifugal force excerted by the traveller on the yarn, the particles from the fibre
    fall on the ring where the traveller is in contact. These particles act like a lubricating film between
    ring and traveller.

    RUBBER COTS AND APRON:

  • For processing combed cotton, soft cots (60 to 65 degree shorehardness) will result in lower U%,
    thin and thick places.
  • There are different types of cores (inner fixing part of a rubber cot)available from different manaufacturers.
    Aluminimum core,PVC core,etc. It is always better to use softer cots with aluminium core.
  • When softer cots are used, buffing frequency should be reduced to 45 to 90 days depending upon
    the quality of the rubber cots, if the mill is aiming at very high consistent quality in cotton counts.
  • If the lapping tendency is very high when processing synthetic fibres for non critical end uses,
    It is better to use 90 degree shore harness cots, to avoid cots damages. This will improve the working and the yarn quality compared to working with 83 degree shore hardness.
  • If rubber cots damages are more due to lapping, frequent buffings as high as once in 30 days will be
    of great help to improve the working and quality. Of course,one should try to work the ringframe without lapping.

    The basic reasons for lapping in the case of processing synthetic fibre is

  • End breaks
  • Pneumafil suction
  • rubber cots type
  • fibre fineness
  • Oil content(electrostatic charges)
  • department temprature and humidity
  • Almost all the lappings orginate after an end break. If a mill has an abnormally high lapping problem
    the first thing to do is to control the end breaks,
    1. after doffing
    2. during speed change
    3. during the maximum speed
    by optimising the process paramters.
  • It is obvious that fine fibres will have a stronger tendency to follow the profile of the roller.
    Therefore lapping tendency will be more.
  • If the fibre is fine, the number of fibres in the cross section will be more, therefore lapping frequency
    will be more.
  • If the pressure applied on the roller is more, then lapping tendancy will be more. Hence fine
    and longer fibres will have more tendency for lapping because of high top roller pressure required to
    overcome the drafting resistance.
  • If the pneumafil suction is less, the lapping tendency will be more both on top and bottom roller.
    But the pneumafil suction depends on the fan diamater, fan type, fan speed, duct design, length of the
    machine, profile of the suction tube etc. If any one of the above can be modified and the suction can
    be improved, it is better to do that to reduce the lapping.
  • The closer the setting between the suction nozzle and the bottom roller, the higher the suction
    efficiency and lower the lapping propensity.
  • Higher roving twist will reduce the lapping tendency to some extent. Therefore it is better to
    have a slightly higher roving twist, provided there is no problem in ringframe drafting, when
    the lapping tendency is more
  • With Softer rubber cots lapping tendency will be more due to more surface contact.
  • The most minute pores, pinholes in the rubber cots or impurities in the cots can cause lapping. Therefore the
    quality of buffing and the cots treatment after buffing is very important. Acid treatment is good
    for synthetic fibres and Berkolising is good for cotton.
  • Electrostatic charges are troublesome especially where relatively large amount of fibre are
    being processed in a loose state e.g drawframe, card etc.Lapping tendency on the top roll increases
    with increasing relative humidity. The frequently held opinion is that processing performace remains
    stable at a steady absolute relative humidity, i.e. at a constant moisture content per Kg of dry air.

    TWIST:
    The strength of a thread twisted from staple fibres increases with increasing twist, upto certain level.
    Once it reaches the maximum strength, further increase in twist results in reduction in yarn strength

  • Coarser and shorter fibres require more Twist per unit length than finer and longer fibres.
  • Twist multiplier is a unit which helps to decide the twist per unit length for different counts
    from the same raw material.This is nothing but the angle of inclination of the helical disposition
    of the fibre in the yarn. This is normally expressed as

    TWIST PER INCH = TWIST MULTIPLIER * SQRT(Ne)

  • If the two yarns are to have the same strength, then the inclination angles must be the same.
  • For 40s combed knitting application, if the average micronaire of cotton is 3.8 and the 2.5% span length
    is around 29 mm, Twist multiplier of 3.4 to 3.5 is enough . If the average micronaire is around 4.3,
    it should be around 3.6 to have better working in Ring frame.
  • cotton combed knitting T.M. = 3.4 to 3.6
  • cotton combed weaving T.M. = 3.7 to 3.8
  • cotton carded knitting T.M. = 3.8 to 4.0
  • cotton carded weaving T.M. = 3.9 to 4.2

    The above details are for cottons of 2.5% span length of 27 to 30 mm and the average Micronaire
    of 3.7 to 4.4. For finer and longer staple, the T.M. will be lower than tha above.

    In general for processing poly/viscose , the T.M. is as follows

  • 51 mm, 1.4 denier fibre : T.M. = 2.7 to 2.9 for knitting application
  • 51 mm, 1.4 denier fibre : T.M. = 2.9 to 3.1 for weaving application
  • 44 mm, 1.2 denier fibre : T.M. = 2.9 to 3.0 for knitting application
  • 44 mm, 1.4 denier fibre : T.M. = 3.0 to 3.1 for knitting application
  • 38 mm, 1.2 denier fibre : T.M. = 3.1 to 3.3 for knitting application
    The above detail is self explanatory

    OTHERS:

    The following ROVING parameters will affect the ring frame process parameters

  • Roving T.M.
  • Bobbin weight
  • Bobbin height
  • Higher the roving T.M., wider the back bottom roller setting or higher the break draft in ring frame.

  • For combed material the creel height should be as low as possible in ringframe.
  • Very long creel heights in ringframe, lower roving T.M. and heavier roving package will result in
    many long thin places in the yarn.(especially in combed hosiery counts)
  • In general 16 x 6 " bobbins are used. This helps to increase the spare rovings per machine with
    higher creel running time. Therefore one should aim at increasing the bobbin weight as well as increasing  the number of spare rovings in the ring frame.
  • Normally 6 row creels are used in modern ring frames. Six row creels will accomodate more spare rovings compared to 5 row creels.(around 150 rovings for 1000 spindle machine.) Creel height should be as low as possible for cotton combed counts.Spare rovings will improve the operators efficiency.
  • Shorter machines are always better compared to longer machines. But the cost per spindle will go up.
    For cotton , polyester/cotton blends, poly/viscose(upto 44mm length), number of spindles upto 1200, should not be a problem. But maintenance is more critical compared to shorter machines.
  • For synthetic fibres with very high drafting resistance, it is better to use shorter machines,
    because the load on break draft gears and on second bottom rollers will be extremely high. If long
    machines are used and the maintenance is not good for such application, the bearing damages, gear damages, bottom roller damages etc. will increase. This will result in coarse counts, higher count C.V., long thinand thick places.
  • Four spindle drive is always better compared to Tangential belt drive. Because small variation in
    machining accuracy of bolster , spindle beam etc will affect the spindle speeds, thereby the twist
    per inch. Waste accumulation between contact rollers, bent contact rollers, damaged contact rollers,
    oil spilling from any one spindle etc. will affect the spindle speeds and thereby TPI. The spindle
    speed variation between spindles in a 5 year old ringframe will be verh high incase of tangential belt
     drive compared to 4 spindle drive.
  • Noise level and energy consumption will be low in 4 spindle drive compared to Tangential belt drive.
  • Compared to Contact rollers, Jockey pully damages are nil. I have worked with 20 year old ring frames with Jocky pulleys,but the variations in spindle speed between spindles is very less compared to a 5 year old ringframe with Tangential belt drive. I have made this comment based on my personal experience.
  • When processing coarse counts at higher speeds, the air current below the machine is a big problem with 4 spindle drive . This is due to the more running parts like tinrollers and jockey pullys. This will lead to more fluff in the yarn, if humidification system is not good enough to suck the floating fluff.
  • If spindle speeds is high for cotton counts, every end breaks will result in more fluff in the
    department due to the free end of the yarn getting cut by the traveller when the distance between
    traveller and the bobbin with the yarn is less. Higher the delay in attending the end break , higher the
    fly liberation.If the number of openings of return air system for a ringframe is less and the exhaust
    air volume is not sufficient enough, then fly liberation from an end break will increase the endbreaks
    and thereby will lead to multiple breaks. End break due to a fly entering the traveller will get struck
    with the traveller and will result in heavier traveller weight and that particular spindle will continue
    to work bad.
  • Multiple breaks are very dangerous, as it will result in big variation in yarn hairiness and
    the ringframe working will be very badly affected due to heavier travellers because of the fluff in the
    traveller.
  • Dry atmosphere in ringframe department will result in more yarn hairiness, more fly liberation
    and more end breaks.
  • It is a good practice to change spindle tapes once in 24 months.Worn out spindle tapes will result
    in tpi variations which is determinetal to yarn quality.

Page 1   2


 Go Back

 Go to Top of Page